2. Remove the front bumper from the car.
3. Disconnect the connector.
4. Remove the ambient temperature sensor.
5. Installation is made in an order, the return to removal.
Removal and installation of the ambient temperature sensor
1. Disconnect the negative battery terminal.
2. Remove the front bumper from the car.
3. Disconnect the connector.
4. Remove the ambient temperature sensor.
5. Installation is made in an order, the return to removal.
2. Remove the front bumper from the car.
3. Disconnect the connector.
4. Remove the ambient temperature sensor.
5. Installation is made in an order, the return to removal.
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Previous
Next
Removal and installation of the mixing damper drive
Removal and installation of the fan motor
Removal and installation of the intake damper drive
Climate control
Air conditioning system
Removal and installation of heater hoses
Removal and installation of back air ducts of a heater
Removal and installation of forward air ducts of a heater
Removal and installation of the ventilation unit
Cabin filter
Removal and installation of the fan motor
Removal and installation of the intake damper drive
Climate control
Air conditioning system
Removal and installation of heater hoses
Removal and installation of back air ducts of a heater
Removal and installation of forward air ducts of a heater
Removal and installation of the ventilation unit
Cabin filter
More articles on repairing other Mazda models
Removal and installation of the sensor-distributor ignition Mazda Familia 5 (1985-1989)
Water temperature sensor (EGI) — check, removal and installation Mazda Capella 3 (1982-1992, petrol)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda3 BK (2003-2009)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda6 GG (2002-2008)
Removal and installation of the fuel pump and fuel quantity sensor Mazda 121 (3) (1996-2003)
Removal and installation of the sensor-distributor ignition Mazda Familia 5 (1985-1989)
Water temperature sensor (EGI) — check, removal and installation Mazda Capella 3 (1982-1992, petrol)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda3 BK (2003-2009)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda6 GG (2002-2008)
Removal and installation of the fuel pump and fuel quantity sensor Mazda 121 (3) (1996-2003)
Link in different formats to this article
TEXTHTMLBB Code
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- User manual
- Maintenance
- Power unit
- Petrol engines 2.0 l
- Petrol engines 2.5 l
- Diesel engines 2.2 l
- Cooling system
- Lubrication system
- Supply system
- Control system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Drive shafts and cardan
- Chassis
- Wheels and tires
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Security systems
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Electrical circuits
MazBook.ru © 2018–2024 · Mobile version · Articles and news · Sitemap: EN BG BY UA RS HR RO PL SK HU · Feedback · Site search · Add to bookmarks
Familia 5 (BF) · Familia 6 (BG) · Capella 3 (GC) · Capella 3 and 4 (GC) · Capella 5 (GE) · Capella 6 (GF) · Mazda3 BK · Mazda6 GG · CX-5KE · Mazda 121 (3) · Mazda BT-50 (1) ·