Internal elements of the body and interior Mazda CX-5 (KE)

Interior — device
1. Deflectors. 2. Speaker grilles. 3. The visor of the instrument cluster. 4. Central panel. 5. Decorative panel. 6. Dashboard. 7. Front side trim. 8. Floor insulation....

Steering column cover
Removal and installation of a casing of a steering column 1. Lower the steering wheel. 2. Squeezing the areas shaded in the figure with your fingers, pry off the upper...

Removal and installation of the bottom cover of the instrument panel
1. Disconnect the negative battery terminal. 2. Remove the decorative panel. 3. Grasping the areas shaded in the figure, pull the center panel in the direction of the...

Removing and installing the bottom panel
Driver side 1. Disconnect the negative battery terminal. 2. Remove the following parts: Driver's door sill trim. Side trim on the driver's side. Versions with navigation...

Removal and installation of the dashboard
1. Disconnect the negative battery terminal. 2. Remove the following parts: Wiper blades. Hood grille. Wiper drive. Front door sills. Front side panels. Glove box....

Removal and installation of a glove box
1. Pressing the glove box in the direction of the arrow (1), unhook A. 2. Pulling the damper strut in the direction of the arrow (2) in the figure, unhook B. Attention....

Front console box
Note. Apply protective tape to the area indicated in the figure. 1. Insert a tape-wrapped flat-bladed screwdriver into the position indicated by the arrow in the figure...

Removal and installation of the switching panel
Versions with automatic transmission 1. Disconnect the negative battery terminal. 2. Move the selector lever to the neutral position. 3. Remove the front console box. 4....

Removal and installation of the upper console
1. Disconnect the negative battery terminal. 2. Remove the following parts: Front console box. Versions with manual transmission: shift knob. Switch panel. 3. Open the...

Removal and installation of the rear console
1. Disconnect the negative battery terminal. 2. Remove the following parts: Front console box. Versions with manual transmission: shift knob. Switch panel. Top panel. 3....

Removal and installation of side walls
1. Pulling the side wall in the direction of the arrows in sequence (1), (2), remove it by disconnecting hooks A and clips B. 2. Pulling the side wall in the direction...

Removal and installation of the forward console
Attention. Apply protective tape to the places indicated in the figure. 1. Disconnect the negative battery terminal. 2. Remove the following parts: decorative panel....

Removal and installation of facing of a rack And
1. Partially unscrew the door seal. 2. Grasping the areas shaded in the figure, pull the A-pillar trim in the direction of the arrow (1), to detach clips A and B. Note:...

Removal and installation of the bottom facing of a rack B
1. Remove the front door sill trim. 2. To remove an overlay of a threshold of a back door. 3. Partially fold back the door seals. 4. Grasping the areas shaded in the...

B-pillar upper trim
1. Remove the following parts: Front door sill trim. Rear door sill trim. B-pillar bottom trim. Top adjustable seat belt anchor cover. Bolts of fastening of the top...

Removal and installation of facing of a rack With
1. Disconnect the negative battery terminal. 2. Remove the following parts: Trunk floor. Trunk lining. Rear door sill trim. Side lining of the trunk. D-pillar trim. 3....

Removal and installation of facing of a rack D
1. Disconnect the negative battery terminal. 2. Remove the following parts: Trunk floor. Trunk lining. Rear door sill trim. Side lining of the trunk. 3. Taking hold of...

Removal and installation of forward lateral facing
1. Remove the front door sill trim. 2. Partially unscrew the door seal. 3. Loosen the cap nut. 4. Pulling the front side trim in the direction of the arrow in the...

Removal and installation of an overlay of a threshold of a forward door
1. Grasping the areas shaded in the figure, disconnect the bar A by pulling the front door sill trim in the direction of the arrow (1) in the figure, and then detach...

Rear door sills
Removal and installation of overlays of thresholds of back doors 1. Grasping the areas shaded in the figure, disconnect the bar A by pulling the rear sill trim in the...

Internal decorative overlay
Removal and installation of an internal decorative overlay 1. Grasping the area shaded in the figure, pull the inner decorative trim in the direction of the arrow (1),...

Removing and installing door trim
1. Disconnect the negative battery terminal. 2. Front doors: Remove interior trim. 3. Insert a flat screwdriver wrapped with electrical tape into the arrow indicated in...

Removal and installation of the trunk floor
1. Remove the fasteners. 2. Remove the trunk floor. 3. Installation is carried out in the reverse order.

Removal and installation of a facing flange of a luggage carrier
1. Remove the boot floor. 2. Partially unscrew the tailgate seal. 3. Remove the fasteners. 4. Grasping the areas shaded in the figure, disconnect the strips A by pulling...

Removal and installation of lateral facing of a luggage carrier
1. Disconnect the negative battery terminal. 2. Remove the following parts: Trunk floor. Trunk lining. Rear door sills. 3. Pry cover A in the direction of the arrow (1)...

Removal and installation of the boot floor
1. Remove the trunk floor to the side. 2. Remove the underfloor of the trunk No. 1 in the direction of the arrow (1) on the image. Versions with a spare wheel 3. Remove...

Removal and installation of the top covering of a door of a luggage carrier
1. Grasping the areas shaded in the figure, disconnect the bar A by pulling the upper trim of the tailgate in the direction of the arrow (1) in the figure, then detach...

Removal and installation of a side covering of a door of a luggage carrier
1. Remove the top trim of the tailgate. 2. Remove retainer A. 3. Grasping the areas shaded in the figure, pull the tailgate side trim in the direction of the arrow (1),...

Removal and installation of the bottom trim of the tailgate
1. Remove the following parts: The upper trim of the tailgate. Side trim of the tailgate. 2. Remove the tailgate recess: Inserting a tape-wrapped flat-bladed screwdriver...

Removal and installation of facing of a ceiling
1. Disconnect the negative battery terminal. 2. Remove the following parts: Versions with sunroof: sunroof seal. A-pillar trims. Navigation lamps. Sun visors. Front door...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Body: Interior (internal elements) Mazda Capella 3 and 4 (1982-1992)
• Body: Interior (internal elements) Mazda6 GG (2002-2008)
• Body: Interior (internal elements) Mazda 121 (3) (1996-2003)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

CX-5KE (2012-2017)