Note:
- Standard connecting rod bolt length: 145.2-145.8mm.
- The maximum allowable length of the connecting rod bolt: 146.5 mm.
Checking the cylinder head bolts
Measure the length of each bolt. If the measured value exceeds the limit, replace the bolt with a new one.
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Previous
Next
Checking the camshafts
Checking valve springs
Checking the valves and valve guides of the gas distribution mechanism
Checking / repairing the valve seat of the gas distribution mechanism
Checking the cylinder head of the gas distribution mechanism
Cylinder head assembly
Installing the cylinder head
Removing the cylinder head
Removal and installation of a head of the block of cylinders
Checking the electrical phase shifter
Checking valve springs
Checking the valves and valve guides of the gas distribution mechanism
Checking / repairing the valve seat of the gas distribution mechanism
Checking the cylinder head of the gas distribution mechanism
Cylinder head assembly
Installing the cylinder head
Removing the cylinder head
Removal and installation of a head of the block of cylinders
Checking the electrical phase shifter
Replacing valve guides
Possible malfunctions of hydraulic gap compensators
Replacing the front crankshaft oil seal
Replacement of a back epiploon of a cranked shaft
Disassembly of the cylinder block and connecting rod piston group
Assembly of the cylinder block and connecting rod and piston group
Checking the block of cylinders
Checking the oil nozzles of the cylinder block
Checking the cylinder block pistons
Check of piston rings of the block of cylinders
Possible malfunctions of hydraulic gap compensators
Replacing the front crankshaft oil seal
Replacement of a back epiploon of a cranked shaft
Disassembly of the cylinder block and connecting rod piston group
Assembly of the cylinder block and connecting rod and piston group
Checking the block of cylinders
Checking the oil nozzles of the cylinder block
Checking the cylinder block pistons
Check of piston rings of the block of cylinders
More articles on repairing other Mazda models
Tightening cylinder head bolts Mazda Familia 6 (1989-1994)
Cleaning and checking the cylinder head Mazda Capella 3 and 4 (1982-1992)
Checking the cylinder head Mazda3 BK (2003-2009)
Checking the cylinder head bolts Mazda6 GG (2002-2008)
Removing the cylinder head Mazda 121 (3) (1996-2003)
Tightening cylinder head bolts Mazda Familia 6 (1989-1994)
Cleaning and checking the cylinder head Mazda Capella 3 and 4 (1982-1992)
Checking the cylinder head Mazda3 BK (2003-2009)
Checking the cylinder head bolts Mazda6 GG (2002-2008)
Removing the cylinder head Mazda 121 (3) (1996-2003)
Link in different formats to this article
TEXTHTMLBB Code
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- User manual
- Maintenance
- Power unit
- Petrol engines 2.0 l
- Petrol engines 2.5 l
- Diesel engines 2.2 l
- Cooling system
- Lubrication system
- Supply system
- Control system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Drive shafts and cardan
- Chassis
- Wheels and tires
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Security systems
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Electrical circuits
MazBook.ru © 2018–2024 · Mobile version · Articles and news · Sitemap: EN BG BY UA RS HR RO PL SK HU · Feedback · Site search · Add to bookmarks
Familia 5 (BF) · Familia 6 (BG) · Capella 3 (GC) · Capella 3 and 4 (GC) · Capella 5 (GE) · Capella 6 (GF) · Mazda3 BK · Mazda6 GG · CX-5KE · Mazda 121 (3) · Mazda BT-50 (1) ·