Note:
- The clutch travel sensor is only installed on vehicles with the i-stop system.
- The clutch stroke sensor is built into the clutch master cylinder.
1. Replace the clutch master cylinder with a new one.
Removal and installation of the clutch travel sensor
1. Replace the clutch master cylinder with a new one.
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Previous
Next
Removal and installation of the clutch master cylinder
Removal and installation of the switch of blocking of a starter
Removing and installing the clutch pedal position sensor
Removal and installation of the clutch pedal
Clutch pedal
Clutch Fluid Replacement / System Bleeding
Checking for Clutch Fluid Leaks
Checking the clutch fluid level
D66M-R, D66MX-R clutch — technical data
C66M-R, C66MX-R clutch — technical data
Removal and installation of the switch of blocking of a starter
Removing and installing the clutch pedal position sensor
Removal and installation of the clutch pedal
Clutch pedal
Clutch Fluid Replacement / System Bleeding
Checking for Clutch Fluid Leaks
Checking the clutch fluid level
D66M-R, D66MX-R clutch — technical data
C66M-R, C66MX-R clutch — technical data
More articles on repairing other Mazda models
Removal and installation of the sensor-distributor ignition Mazda Familia 5 (1985-1989)
Water temperature sensor (EGI) — check, removal and installation Mazda Capella 3 (1982-1992, petrol)
Removal and installation of the crankshaft position sensor (diesel) Mazda3 BK (2003-2009)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda6 GG (2002-2008)
Removal and installation of the fuel pump and fuel quantity sensor Mazda 121 (3) (1996-2003)
Removal and installation of the sensor-distributor ignition Mazda Familia 5 (1985-1989)
Water temperature sensor (EGI) — check, removal and installation Mazda Capella 3 (1982-1992, petrol)
Removal and installation of the crankshaft position sensor (diesel) Mazda3 BK (2003-2009)
Removal and installation of the vehicle speedometer sensor (without anti-lock braking system) Mazda6 GG (2002-2008)
Removal and installation of the fuel pump and fuel quantity sensor Mazda 121 (3) (1996-2003)
Link in different formats to this article
TEXTHTMLBB Code
Comments and feedback from visitors
No comments yet
- General information
- Introduction to the guide
- User manual
- Maintenance
- Power unit
- Petrol engines 2.0 l
- Petrol engines 2.5 l
- Diesel engines 2.2 l
- Cooling system
- Lubrication system
- Supply system
- Control system
- Intake and exhaust system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Transfer case
- Drive shafts and cardan
- Chassis
- Wheels and tires
- Front suspension
- Rear suspension
- Brake system
- Steering
- Body
- Exterior (external elements)
- Interior (internal elements)
- Security systems
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Electrical circuits
MazBook.ru © 2018–2024 · Mobile version · Articles and news · Sitemap: EN BG BY UA RS HR RO PL SK HU · Feedback · Site search · Add to bookmarks
Familia 5 (BF) · Familia 6 (BG) · Capella 3 (GC) · Capella 3 and 4 (GC) · Capella 5 (GE) · Capella 6 (GF) · Mazda3 BK · Mazda6 GG · CX-5KE · Mazda 121 (3) · Mazda BT-50 (1) ·