Equipment and devices Mazda 626 (5)

General description of electrical equipment
The electrical system has a voltage of 12 volts with a negative ground. Power for the headlights and all electrical components comes from a lead-acid battery, which is...

Finding the source of a malfunction in the electrical system
Finding the source of the problem Insert a thin probe from the back of the connection socket so that it touches the desired terminal - connect a voltmeter to the probe....

Fuses — location and replacement
Removing the fuse box cover Fuse box in the engine compartment Checking the status of the fuse box 1. Blown fuse 2. A whole fuse The electrical circuits of the car are...

Circuit breakers
On some models, the circuit breakers turn on automatically. If the switch does not close automatically, check the circuit it is protecting immediately. Some switches...

Relay — check and replace
Relay test Check that the relay opens the circuit when there is no voltage and closes the circuit when voltage is applied. Some vehicle electrical components use relays...

Turn Signal / Alarm Interrupter
When the breaker is operating, distinct clicks should be heard. If the direction indicators on both sides of the vehicle do not work, check the fuse, breaker and...

Steering column switches
Switch Terminal Identification - Pre-1997 Models Steering Column Switch Conductivity Chart - Pre-1997 Models Combination switch Switch position Conductivity between...

Ignition switch and lock drum
Ignition Switch Terminal Identification Ignition switch conductance table Key position in the ignition lock Conductivity between terminals Ass 2 and 6 On 2, 4 and 6; 1...

Switches on the instrument panel
Mazda Models Rear Defroster Switch Terminal Identification When switched on, there must be continuity between terminals B and C. Defroster Switch Terminal Identification...

Dashboard Tools
Examination 1. Check the integrity of the fuses. 2. Disconnect the connection connector from the sensor of the corresponding device and ground it. Turn on the ignition...

Instrument panel — removal and installation
Removing 1. Disconnect the negative battery cable. 2. Remove trim panel. 3. Loosen the fixing screws. 4. Disconnect the connectors and remove the instrument panel....

Radio and speakers — removal and installation
Removing Radio 1. Disconnect the negative battery cable. 2. Remove the appropriate trim panel. 3. Insert the special tools into the holes on the radio panel and remove...

Radio Antenna — Replacement
The installed antenna can be fixed or with an electric lift. Replacement 1. Unscrew the antenna with a wrench. 2. Remove the antenna mount with pliers. 3. Remove the...

Headlight bulbs — replacement
Replacement 1. Open the hood. Models of Ford Probe 2. Disconnect the negative battery cable. 3. Loosen the fixing screws and remove the outer casing. 4. Unscrew the...

Headlights
There are two adjusting screws for adjusting the position of the headlights. Headlight adjustment diagram Adjust the headlights using the diagram below. When adjusting...

Headlight drive
Examination 1. Check for a blown jumper in the engine compartment fuse box. 2. Check the power supply to the headlight drive. Check connecting wires and drive switch. If...

Bulb replacement
Front direction indicators / sidelights 1. On Ford Probe models, remove the mounting screws and fold back the edge of the wheel arch insert to access the bulb. 2. On...

Wiper motor — check and replacement
Examination 1. Check the wiper fuse. Check the voltage supply to the wiper motor. 2. Check the operation of the wiper motor, as well as wires and connections. When...

Horn of a sound signal — check and replacement
Examination 1. Disconnect connection connectors (A) and mounting bolts (IN) horns. 2. Check the operation of the horn by applying battery voltage to it. 3. Check the...

Daytime running lights
This system is installed on models for the Canadian market. It turns on the headlights every time the engine is started. The headlights are less bright when the system...

Rear window heater — check and repair
Small breaks in the heated rear window heating elements can be repaired without removing the rear window. Examination 1. Check the heater fuse, switch, relay and...

Cruise control system
The cruise control system maintains a set vehicle speed using an electronic control unit, a speed sensor and a drive located in the engine compartment. The cruise...

Electric windows
The power window system consists of a switch, electric drives, power window mechanisms and connecting wires. Window Central Switch Conductivity Chart - Ford Probe Models...

Central locking and remote control of the central locking
The central locking system consists of switches, actuators and connecting wires. Examination 1. If a malfunction is detected, first of all, check the fuses. 2. Try...

Electric Rear View Mirror
Power mirrors use two electric motors to adjust the position of the glass. Mirror Adjuster Continuity Check - Ford Probe Models Switch position Terminal voltage Left...

Top hatch
The top hatch opens and closes with a single electric motor. Terminal Identification and Conductivity Chart of Sunroof Drive Switch Switch position Conductivity between...

Airbag — removal and installation
Electronic control unit for the airbag system (indicated by an arrow). The additional passive safety system consists of an electronic control unit, two collision sensors...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Electrical equipment: Equipment and devices Mazda Familia 6 (1989-1994)
• Electrical equipment: Equipment and devices Mazda3 BK (2003-2009)
• Electrical equipment: Equipment and devices Mazda6 GG (2002-2008)
• Electrical equipment: Equipment and devices Mazda CX-5KE (2012-2017)
• Electrical equipment: Equipment and devices Mazda BT-50 (1) (2006-2011)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code

Capella 5 (1991-1997)