Doors, locks and windows of the car Mazda 121 (3)

Removal and installation of the door
Removing Unscrew the bolt (2) and remove the door lock (1). If so, turn the plug (3) to the left and remove it. Pull out the fasteners (5) from a hinged finger. Pull out...

Removal and installation of a core of the lock of a door
Removing Mark the position of the lock rod (1), for which circle the rod with a felt-tip pen. Unscrew the two Tox screws (2) special key and remove the rod. Installation...

Removal and installation of the external door handle
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory units. See instructions in...

Removal and installation of the cylinder of the door lock
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory blocks. See instructions in...

Removal and installation of the door lock
Removing Disconnect the negative cable from the battery. Attention: This will erase the data from the electronic memory blocks. See instructions in chapter « electrical...

Rear doors of the Ford Fiesta Courier
1. Right door; 2. Left door; 3. Loop; 4. Top mounting plate; 5. Bottom mounting plate; 6. Reinforcing plate; 7. Hex bolt with washer; 8. Hex bolt with washer; 9. Nut;...

Removal and installation of the lock of a back door (Ford Fiesta Courier)
Removing Unhook the rear door trim. Unscrew the screws securing the lock cover and wire «masses». Unhook the top link. To do this, press out the holder (2) and pull the...

Removal and installation of facing of a door
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory units. See instructions in...

Removal and installation of the internal door handle
Removing Disconnect the negative cable from the battery with the ignition off. This will erase the data from the electronic memory units. See instructions in chapter «...

Removal and installation of door glass
Removing Disconnect the negative cable from the battery with the ignition off. This will erase the data from the electronic memory units. See instructions in chapter...

Removal and installation of a window regulator
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory units. See chapter «...

Removing and installing the trunk lid
Removing Attention: To make it easier to install electrical wires and hoses, tie pieces of cord to their ends before removing them. The cord remains connected in the...

Removal and installation of the trunk lid lock cylinder
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory blocks. See instructions in...

Removal and installation of the trunk lid lock
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data from the electronic memory blocks. See instructions in...

Ford KA: Removal and installation of the door
Removing Unscrew the screw securing the door opening limiter (1). If so, turn the plug (2) to the left and disconnect it. Loosen the fixing screws (3) hinged finger....

Ford KA: Removal and installation of the outer door handle
Note: The operations for this spreader are the same as those described for the Ford Fiesta/Mazda 121 models. Note the following differences. Removing Use a sharp knife...

Ford KA: Removal and installation of the door lock cylinder
Note: The operations in this section correspond to those described for the Ford Fiesta/Mazda 121 models. Note the following differences. Removing Remove rear door window...

Ford KA: Removal and installation of the door lock
Note: The operations for this section correspond to those described for the Ford Fiesta/Mazda 121 models. Note the following differences. Removing Remove rear door...

Ford KA: Removing and installing door trim
Removing Disconnect the negative cable from the battery with the ignition off. Attention: This will erase the data of the electronic memory units. See instructions in...

Ford KA: Removal and installation of a support of facing of a luggage carrier
Removing Remove trunk lining. Fold back the rear seat. Unscrew the three bolts of the trunk lining support and remove the support. Installation Install the support and...

Ford KA: Removal and installation of the inner door handle drive
Removing Remove door trim. Pull off the protective film in the drive area of the inner door handle, fold it down and secure with adhesive tape. Unscrew the screws...

Ford KA: Removing and installing door glass
Removing Remove door trim. Loosen the four screws securing the loudspeaker. Unplug and remove loudspeaker. Loosen the screws of the inner door handle drive and unhook...

Ford KA: Removing and installing power window
Removing Remove door glass. Manual window regulator: drill out five rivets. Power window: drill out four rivets and remove three bolts. Remove the power window motor...

Ford KA: Removal and installation of the trunk lid lock cylinder
Removing Remove trim from trunk lid. To do this, open it. Unscrew the plastic screw above the inner handle and then pry out the sliding clamp with a screwdriver. Unhook...

Ford KA: Removing and installing trunk lid lock
Removing Unhook the drive rod from the lock cylinder. Unscrew the two bolts securing the lock and remove it. Installation Insert the lock into the trunk lid and secure...

This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian

More sections on repairs of other Mazda models
• Body: Doors and windows Mazda Familia 6 (1989-1994)
• Body: Doors, windows and locks Mazda Capella 6 (1997-2005, petrol)
• Body: Doors and windows Mazda3 BK (2003-2009)
• Body: Doors and windows Mazda6 GG (2002-2008)

Share with friends on social networks:

Link in different formats to this section

TEXTHTMLBB Code